Open daily 7 AM – 10 PMFree site inspection in Riyadh
Chat on WhatsAppCall us now · +966 55 725 1134
Artificial grass planning

Artificial Grass Roll Width and Cutting Plan in Riyadh: Cutting Waste and Seams

Artificial grass is usually sold in rolls of a fixed width, so knowing the area of your space is not enough. The roll width, the way it is cut and the direction of the pile decide how many rolls you need, how many seams will show in the floor and how much waste you pay for. This page explains how we plan the cuts before you order, so you get a clean lawn with as little waste as possible anywhere in Riyadh.

Green artificial grass laid in a villa garden in Riyadh
An artificial grass sample showing two different pile heights
A plan before cuttingWe draw the area on paper first
Free site visitMeasuring the area inside Riyadh
A cutting planBefore ordering and supply
Samples to viewDifferent heights and colours
DailyWe take requests 7 am – 10 pm
Roll width

Why does roll width matter more than total area?

A fixed-width, variable-length roll

Artificial grass is produced in rolls of a set width and the length you need is cut from it. This means that an area of 28 square metres can need a different quantity depending on its shape. A space 4 metres wide and 7 metres long may be covered with a single piece if the available roll is 4 metres wide, but needs two pieces and a seam if the roll is narrower. We confirm the widths available at the time of your order.

Width and waste

When the width of your space does not match the roll width, the offcuts are lost. The closer your dimensions are to the roll width, the less waste there is. So we draw the area first and test more than one layout before deciding the number of metres, instead of simply multiplying length by width.

Seams are not a flaw when done well

A well-made seam on a flat base with proper tape is barely visible, but it remains a sensitive point. We try to reduce their number and place them in low-visibility spots away from walking paths where we can. Joining is explained in joining and edging.

Cutting plan

How do we plan the cuts before ordering the material?

We follow a simple sequence that gives you a realistic figure in metres instead of a rough guess.

Measure the area accurately

We measure each side and record columns, trees, openings and curved edges.

Draw the layout

We draw the shape and lay the roll width over it to see how many pieces are needed and where the seams fall.

Test the roll direction

We try the roll running along the length and across the width and compare the waste in each case.

Work out the metres required

We total the lengths of all the pieces and add a small margin for levelling and edges.

Check pile and direction

We make sure the pile direction is the same in every piece so there is no colour difference between one piece and the next.

Fix the seam positions

We mark each seam on the drawing and agree it with you before the work.

Seams and direction

Mistakes that show in the lawn after fitting

Different pile directions

Two pieces from the same roll laid in different directions look like two colours. One direction is essential for a uniform look.

Seams in the walking path

A seam in the busiest path is the first to wear and the first to catch the eye.

Cutting with no margin

Being short by a few centimetres at the edges can hold up the whole job. We leave a small margin and then trim precisely on site.

Uneven base under the seam

Any small step shows under a seam, so we prepare the base and drainage first. See base and drainage.

Grass type

Does the calculation change with pile height?

Height does not change the area

Pile height affects the look, the feel and the price, but not the area of your floor. However, some denser or taller types are heavier and less flexible when folded, so they need more care at seams and edges. Choose the right type for your use from the artificial grass heights guide.

Use decides the choice

Home gardens, rooftops, kids’ play areas and outdoor majlis seating each need a different height, density and drainage. Decide the use first, then we plan the rolls around the type you choose.

Edges and curves

Curved edges, tree beds and corners consume more waste. If your space has many curves, expect more waste and tell us so we can draw a dedicated plan.

Before laying

Preparing the base decides the quality of seams and cuts

A flat base before any cutting

Cutting rolls on an uneven surface gives a misleading result, because what looks right on wavy ground can change once it is levelled. So we check flatness and falls first, and only then fix the plan. See grass over tiles, concrete and soil.

Unrolling and relaxing

A roll can keep fold marks after transport, so we leave it unrolled for a short time before the final cut so it settles flat. This makes the edges cleaner and reduces measuring differences.

Drainage and edges

A floor that does not drain weakens the fixing and produces odours. We plan falls and openings together with the cutting plan so we do not have to cut the material later. See base and drainage.

Worked examples

Simple examples of how roll width affects the result

The figures below are hypothetical calculation examples to explain the idea. They are not prices or confirmed dimensions for any specific product.

A 4 × 7 m area

If the roll is 4 metres wide, one piece 7 metres long may be enough with no lengthwise seam.

A 5 × 6 m area

If the roll is 4 metres wide, we need two adjoining pieces and a seam, and waste comes from the second piece.

An L-shaped area

We split it into two rectangles and arrange the pieces to reduce waste, and may reuse a short piece in the corner.

An area with a tree bed

We cut a circle around the bed and keep the cut-out piece for use elsewhere where possible.

Estimate how much you need

Estimate the area before the cutting plan

Enter the length and width to get the area and a suggested quantity after waste. After the visit we turn the figure into an actual roll plan.

0Area (m²)
0Suggested order (m²)
Send these sizes and ask for a price

Questions customers ask

Is there one standard roll width?

Rolls differ between products and suppliers. We confirm the available widths when you order and plan the cuts on that basis.

How do I know how many rolls I need?

Area alone is not enough. We draw the layout, lay the roll width over it and then work out the piece lengths. The calculator here gives a first estimate.

Will the seam show in the grass?

A well-made seam on a flat base with suitable tape is barely visible, but we reduce the number of seams and place them in low-visibility spots.

Why does pile direction matter?

Because the pile reflects light differently depending on direction, two pieces laid in different directions appear as two colours.

Can offcuts be used?

Sometimes in edges and small corners, provided the colour, direction and height match.

Does pile height affect cutting waste?

It does not change the area, but some types are heavier and less flexible and need more care at joins. See artificial grass heights.

Do you handle rooftops and curved gardens?

Yes. We measure the space and plan the cutting by shape, and for rooftops see rooftop artificial grass.

How do I ask for a quotation with a cutting plan?

Send the dimensions and photos of the space by WhatsApp or call us, and we arrange a free visit and then send the metres required and the cutting plan.

Book a free site visit and a cutting plan for your area

Send the measurements or photos of the space and we will arrange a free visit and a clear quotation.

Open daily 7 AM – 10 PMServing Riyadh city

More guides and services you may find useful

Call nowChat on WhatsApp